TIMKEN 558-S-553-SB tapered bearings with Flange
Also known as : 558-S-553-SB
- Inside Diameter: 59.987 mm
- Outside Diameter: 129.944 mm
- Width: 14.288 mm
- Basic dynamic load rating: 191 kN
- Basic static load rating: 248 kN
TIMKEN 558-S-553-SB Bearing
TIMKEN 558-S-553-SB Bearing details
| Series | 555 |
|---|---|
| model | 558-S-553-SB |
| Cone Part Number | 558-S |
| Cup Part Number | 553-SB |
| Design Units | Imperial |
| Cage Type | Stamped Steel |
| Bearing Weight |
2.500 Kg 5.40 lb |
| Dimensions | |
| d - Bore |
59.987 mm 2.3617 in |
| D - Cup Outer Diameter |
129.944 mm 5.1159 in |
| D1 - Flange Outer Diameter |
136.025 mm 5.3553 in |
| B - Cone Width |
36.678 mm 1.4440 in |
| C - Cup Width |
30.163 mm 1.1875 in |
| C1 - Cup Flange Width |
6.350 mm 0.2500 in |
| T - Bearing Width to Flange |
14.288 mm 0.5625 in |
| T1 - Bearing Width |
38.100 mm 1.5000 in |
| Abutment and Fillet Dimensions | |
| R - Cone Backface "To Clear" Radius |
3.600 mm 0.14 in |
| r - Cup Backface "To Clear" Radius |
3.30 mm 0.130 in |
| da - Cone Frontface Backing Diameter |
69.10 mm 2.72 in |
| db - Cone Backface Backing Diameter |
74.90 mm 2.95 in |
| Da - Cup Frontface Backing Diameter |
116.84 mm 4.60 in |
| Ab - Cage-Cone Frontface Clearance |
2 mm 0.08 in |
| Aa - Cage-Cone Backface Clearance |
1.8 mm 0.07 in |
| a - Effective Center Location |
-9.4 mm -0.37 in |
| Basic Load Ratings | |
| C90 - Dynamic Radial Rating (90 million revolutions) |
49400 N 11100 lbf |
| C1 - Dynamic Radial Rating (1 million revolutions) |
191000 N 42900 lbf |
| C0 - Static Radial Rating |
248000 N 55700 lbf |
| Ca90 - Dynamic Thrust Rating (90 million revolutions) |
29300 N 6590 lbf |
| Factors | |
| K - Factor | 1.69 |
| e - ISO Factor | 0.35 |
| Y - ISO Factor | 1.73 |
| G1 - Heat Generation Factor (Roller-Raceway) | 91 |
| G2 - Heat Generation Factor (Rib-Roller End) | 21.1 |
| Cg - Geometry Factor | 0.111 |
As TIMKEN bearing distributor, Nodes bearings have TIMKEN 558-S-553-SB bearings in stock, TSF (Tapered Single with Flange) Imperial , Tapered roller bearings.
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
TIMKEN bearing cross reference