TIMKEN HM231140-HM231115-B tapered bearings with Flange
Also known as : HM231140-HM231115-B
- Inside Diameter: 146.05 mm
- Outside Diameter: 241.3 mm
- Width: 22.225 mm
- Basic dynamic load rating: 597 kN
- Basic static load rating: 932 kN
TIMKEN HM231140-HM231115-B Bearing
TIMKEN HM231140-HM231115-B Bearing details
| Series | HM231100 |
|---|---|
| model | HM231140-HM231115-B |
| Cone Part Number | HM231140 |
| Cup Part Number | HM231115-B |
| Design Units | Imperial |
| Cage Type | Stamped Steel |
| Bearing Weight |
10.100 Kg 22.300 lb |
| Dimensions | |
| d - Bore |
146.050 mm 5.7500 in |
| D - Cup Outer Diameter |
241.300 mm 9.5000 in |
| D1 - Flange Outer Diameter |
250.723 mm 9.8710 in |
| B - Cone Width |
56.642 mm 2.2300 in |
| C - Cup Width |
44.450 mm 1.7500 in |
| C1 - Cup Flange Width |
9.525 mm 0.3750 in |
| T - Bearing Width to Flange |
22.225 mm 0.8750 in |
| T1 - Bearing Width |
57.150 mm 2.2500 in |
| Abutment and Fillet Dimensions | |
| R - Cone Backface "To Clear" Radius |
3.600 mm 0.14 in |
| r - Cup Backface "To Clear" Radius |
3.30 mm 0.130 in |
| da - Cone Frontface Backing Diameter |
160 mm 6.3 in |
| db - Cone Backface Backing Diameter |
164.10 mm 6.46 in |
| Da - Cup Frontface Backing Diameter |
224.03 mm 8.84 in |
| Ab - Cage-Cone Frontface Clearance |
4.8 mm 0.19 in |
| Aa - Cage-Cone Backface Clearance |
3.6 mm 0.14 in |
| a - Effective Center Location |
-11.4 mm -0.45 in |
| Basic Load Ratings | |
| C90 - Dynamic Radial Rating (90 million revolutions) |
155000 N 34800 lbf |
| C1 - Dynamic Radial Rating (1 million revolutions) |
597000 N 134000 lbf |
| C0 - Static Radial Rating |
932000 N 210000 lbf |
| Ca90 - Dynamic Thrust Rating (90 million revolutions) |
84500 N 19000 lbf |
| Factors | |
| K - Factor | 1.83 |
| e - ISO Factor | 0.32 |
| Y - ISO Factor | 1.88 |
| G1 - Heat Generation Factor (Roller-Raceway) | 533 |
| G2 - Heat Generation Factor (Rib-Roller End) | 85.9 |
| Cg - Geometry Factor | 0.133 |
As TIMKEN bearing distributor, Nodes bearings have TIMKEN HM231140-HM231115-B bearings in stock, TSF (Tapered Single with Flange) Imperial , Tapered roller bearings.
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
